TNT Sports

List of the table of contents of this article:

• 1,TNT Sports thinkvision computer enters the system to restore management and how to exit?
• 2, How to exit the laptop when it becomes system mode after power is cut off
• 3, How to exit the student tablet Live system
• 4, How does Lenovo computer exit the PE system?

thinkvision computer enters the system to restore management and how to exit?

1. First, turn on the computer. If the computer has been turned on, restart the computer. Then wait for the logo of the computer to pop up when it is turned on. At this time, keep pressing the "F2" button. Then enter the BIOS mode in the pop-up window.

2. First, press the "Power Button" in the upper left corner of the computer keyboard to turn on the computer. 2. Then wait for the "thinkvision" on the computer screen to start the logo, and then press the "F12" button.3. After a period of time, the computer can enter the BIOS mode interface. 4. Finally, press the "esc" button to exit the BIOS mode directly.

3. Solution: Press the ESC key, exit, and restart the computer. Reason 2: The data cable or power cable of the hard disk has poor contact, causing the motherboard to be unable to recognize the hard disk, so this prompt box pops up. Solution: Cut off the power supply, unplug and plug in the hard disk data cable or power cable again, and turn on the power supply.

4. In my computer window, right-click the disk character you want to clean up - "Properties" - "Clean Disk" - check the file to be deleted - OK - yes. Clear the temporary file, start-run-enter %temp%--OK. Clean up the registry and junk files with the optimization master or super rabbit.

5. The main reason is that there is a problem with the setting of the host BIOS. When the BIOS setting is incorrect, restarting the computer will automatically enter the BIOS. Since it is caused by the setting of BIOS, you only need to set it in the BIOS to solve the problem.

How to exit when the laptop turns into system mode after power is cut off

1. It is recommended to press the power button for a long time until the laptop is out off. Then restart it and have a try.

2. Such a problem may be caused by software conflicts, inappropriate drivers, and system problems. You can restore the system in safe mode, but it still doesn't work. Reinstall the operating system and don't install software, patches, drivers, etc.

3. Because power outage is an abnormal situation, it is likely to cause damage to the system or hard disk. Therefore, if there is an abnormal power outage, the system will be self-checked when restarting, which cannot be changed.

4. Right-click the power supply at the bottom right of the screen and select "Power Options". Open the "Power Options" window and click "Change Computer Sleep Time" on the left. Open the "Edit Plan Settings" window and click "Change Advanced Power Settings". A "Power Options" appears, click "Power Management".

How to exit the student system on the student tablet

1. Use the shortcut key: press the "Ctrl plus Alt plus Delete" combination key, select the "Exit" or "Logout" option to exit the student system.Restart the tablet: Press the power button on the student tablet for a long time, select the "Restart" option, and wait for the tablet to restart before exiting the student system.

2. Find the exit option: First, you need to look for the option to exit the student system in the settings menu of the tablet. This is usually in the settings of "Users and Accounts" or "Systems and Devices". On some tablets, you may need to pull down the notification bar and click the gear icon to enter the settings.

3. Method: First, enter the tablet interface and click "Settings". On the open settings page, click "Advanced Settings". Enter the advanced settings page and click the buoy behind "Student Mode".

4. Exit the student system on the student tablet: find the student mode directly in the settings and click to close it.You can find Restore Factory Settings in the settings and select Restore System. Expand knowledge: The word system comes from the transliteration of the English system, that is, several parts are interconnected and interact to form a whole with certain functions.

5. Kuaiyidian student tablet exits the student system as follows:. Enter the settings user account administrator to exit. Enter your username and password in the pop-up box. Click "Confirm Exit" to exit successfully.

6. In the "Settings" interface, find the "Parental Control" option and click to enter. In the "Parental Control" interface, find the "Learning Mode" option and click to enter. In the "Learning Mode" interface, find the "Exit Learning Mode" option and click to enter. Confirm the prompt to exit the learning mode and enter the correct password.

How does Lenovo computer exit the PE system?

1. How to uninstall the pe system: First, open the run dialog box on the computer (notebook Windows 10). Then, enter "msconfig" in the running dialog box and click OK. Then, click Boot in the open system configuration, click "PE-Windows" in the boot interface, and then click Delete.

2. Steps: Double-click to open the "My Computer" application; select the "Computer Properties" option; click "Advanced Options"; select "Startup and Failover"; click "Default Operating System"; Shut down or restart to exit the PE system.

3. Double-click to open the "My Computer" application;Select the "Computer Properties" option; click "Advanced Options"; select "Startup and Failure Recovery"; click "Default Operating System"; Shut down or restart to exit the PE system.

4. The reason for this situation is that Windows PE is added to its boot project when the system starts up. You can win the Windows PE in the system boot settings to delete and restart to remove it. The specific setting method is as follows: After the computer is turned on, you can see the two options that currently appear.

5. There are two ways to exit the BIOS: if you need to save the settings made in the BIOS before, press F10-Enter to save, and then the system will automatically restart. ; ; If you want to give up the previous modifications, press Ese-return to confirm exit.Then the system will start normally.