100 free bonus casino no deposit GCash

List of Contents of this article:

• 1,100 free bonus casino no deposit GCash What is the difference between the Frank numerical control system and the wide number?
• 2, Frankish System Beginner Tutorial
• 3, How does the Frank system program the arc?
• 4, CNC turning methodHow does the Frank system turn over the program

What is the difference between the Frank numerical control system and the wide number?

Difference 2: The user interface is different, and the parameter settings are different; Difference 3: Fanake is expensive and Guangshu is cheap.

Frank has a separate knife replenishment page and a pair of knife pages. The knife replenishment is in wear and tear. Relatively speaking, Frank's operation is relatively separate, and the wide number is glued together. The price of rn wide number systems is much lower than that of Farak, and the system is also relatively stable. It is quite cost-effective.

The wide number is input by the incremental coordinate U.W, and the knife is directly input in the parameter. Frank has a separate knife repair page and a pair of knife pages. The knife repair is in wear. Relatively speaking, Frank's operation is relatively separate, and the wide number is glued together.

It doesn't make much difference. The difference is that one control panel is in Chinese and the other is in English. Guangshu 980 is a copycat version of Farak.

Frank System Beginner Tutorial

Operation Method: Return to the original point: Adjust the mode and press the Z axis The Z+ icon, return Z first and then return X Y to prevent knife collision.Fast movement: The speed is controlled by the magnification switch, and the magnification switch is invalid before returning to the origin.

Switch the machine tool mode to the "edit" state, as shown in the figure: (2) Press the "" function key on the machine tool operation panel, and then the display interface enters the "program" interface (press twice to achieve the exchange of the coordinate interface and the program interface), as shown in the figure below: (3) Then create a new one by operating the machine tool panel Program.

Set the spindle speed ○ Put the working mode in "MDI" mode; ○ Press the "program key"; ○ Press the "MDI" button at the bottom of the screen; ○ Input the rotation speed and steering (such as "S500M03;" and then press "INSRT"); ○ Press the start button.

Press the "MDI" key, and then press the "Prot Program Control" key to return to the K parameter screen., change K6 and K7 back to "0", and then press the "Save" key to save. The machine tool stops debugging, and then turns off the parameter switch to perform the tool change operation, as shown in the figure below. The above is the teaching of macro program programming in the Frank processing center.

Turn the mode selection knob to "MDI" (manual data input operation) and enter "M03 S400" (general speed 350-400r/min). Twist the mode selection to the "handwheel" mode, as shown in the figure below.

How does the Frank system program the arc?

R is the radius of the arc. When the center angle from the beginning to the end of the arc is less than or equal to 180 degrees, R is a positive value; when the center angle is greater than 180 degrees, R is a negative value.Because when the CNC lathe processes the sphere, the center angle from the starting point to the end point is always less than 180 degrees, so R is generally a positive value.

The inner arc needs to be subtracted from the tip R. Because the X axis is divided by 2 set by the system. THAT IS TO SAY, YOUR X-AXIS WALKS 1MM IN THE COORDINATE. The actual X-axis has only moved 0.5. When you turn around, your diameter is just 1MM less. Therefore, the X axis should be calculated and multiplied by 2.

Use the chamfer function of numerical control, such as G1 Z-10 D5/ Z-5 U20Z, which is a rounded corner of R5 in straight lines and slashes, which is adapted to the GSK980TB system. If it is Frank, it is directly represented by R5. In this way, no steps will appear.

Walking the arc in the G2/G3 format againJust give the F value, and the whole program speed can also be doubled with the machine tool. F is the modal. After the first time the value is given, if there is no F, it will always be the original speed, and the speed will indeed slow down when milling the arc, or try to remove G1Q1.

How to flip the program of the CNC turning frank system

1. First, turn on the parameter switch, and then select the input method, enter the program page, enter the parameter value to be modified, and then press the [Insert] or [Input] key , the modification can be completed.

2. To jump the program, just add a slash (/ ) before the program segment you want to jump, and then turn on the jump key on the operation panel. Program copying should be implemented on the soft keyboard, as if by pressing (EX--...) What kind of. Then the software functions of copying, splitting and inserting will come out.

3. Open the operation interface of the CNC lathe and enter the program editing page. Find options such as "Program Directory" or "Program List" in the operation interface and click to enter. Select the program that needs to be retrieved in the program directory list and click the "Open" or "Edit" button.

4. Operation method: return to the origin: after adjusting the mode, press the Z+ icon on the Z axis, first return Z and then X Y to prevent knife collision. Fast movement: The speed is controlled by the magnification switch, and the magnification switch is invalid before returning to the origin.

5. Handwheel in the program: When the handwheel key in the program is NO, the movement of the handwheel during memory execution can be added to the program. 5 Transformation key: Enter the address or symbol at the bottom right of the address key, press the conversion key and then press the address key.Paper tape execution: perform DNC transmission. 5 Page-turning key: Use this key to turn the indicator forward one page.